Sale!

9.0kw Long axis air cooled spindle motor

221,000

  • 220v/380v 9.0kw Long axis air cooled spindle motor ceramic ball bearings

9 in stock

Description

 Product Package:

  • 220v/380v 9.0kw Long axis air cooled spindle motor ceramic ball bearings

9.0kw Air cooled Spindle

 

9.0kw Long axis air cooled spindle motor ceramic ball bearings

Basic parameters of 9.0kw Air cooled Spindle:

  • Size: 561x141x182.5mm
  • Power: 9.0kw
  • Voltage: 220v/380v
  • Speed: 12000-24000rpm
  • Frequency: 800Hz
  • Current: 30A/20A
  • Pole: 4
  • Bearings Type: 2x7008C DB & 2x7006C DB (4pcs ceramic ball bearings)
  • Cooling Way: 230vAC cooling fan
  • Chunk: ISO30

9.0kw Long axis air cooled spindle motor ceramic ball bearings

 

 

1.5kw ER20 Air Cooled Square Spindle Motor

 

  • Our Ceramic ball bearings spindle use 4 pcs ceramic ball bearings.
  • Ceramic ball bearings are resistant to high temperatures and low heat, usually 3-5 degrees lower than steel ball bearings during using.
  • Ceramic ball bearings have low friction, low noise and long service life.
  • If you want to use the spindle for aluminium, hard wood, then ceramic ball bearings better than steel ball bearings.

 

9.0kw Long axis air cooled spindle motor ceramic ball bearings 9.0kw Long axis air cooled spindle motor ceramic ball bearings 9.0kw Long axis air cooled spindle motor ceramic ball bearings

 

Preparations before use:

  • Spindle working environment temperature is usually -10 ~ 40.
  • Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.

Use Correctly:

  • 9.0kw Air cooled Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter’s specifications and parameter settings need match spindles parameter. (Because of high-speed grease inside the bearing state will change, when you get the spindle, maybe the noise sounds not normal. Please run it 30 minutes or even more, the noise will be normal.)
  • Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.
  • During normal operation, 9.0kw Spindle Motor often encounters the phenomenon of heat, always check whether the air-cooled spindle housing and duct clogging dust. If clogging dust, to promptly clean up. If you do not clean up, it is easily to make the spindle burned.
  • Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts, collets, cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.

Care and Maintenance:

  • Spindle frequency power supply connected rated voltage, it should be consistent with the technical parameters of the spindle; speed can be adjusted by changing the frequency, and voltage is proportional to the change.
  • Spindle being not used; spindle appearance should be oiled. Plus, the shaft protection device, put in a dry place.
  • To replace the spindle bearings, certain professional and technical personnel should be replaced. Supporting special tools, bearings should be replaced fully cleaned without removing the stator coils.

 

Water-cooled spindle and Air-cooled Spindle differences:

  • Cooling in different ways: water-cooled spindle motor uses water cycle to cool the heat generated after the high-speed rotating spindle, whereas air cooled spindle motor uses fan-cooled approach for cooling.
  • Noise: Water-cooled spindle motor is basically no noise, but the air-cooled spindle motor is very loud.
  • Life aspects: Water-cooled spindle motor pay attention to maintenance, frequently changes the water or the use of industrial water coolers, air-cooled spindle fan mainly by the wind blowing the heat transferred to the heat sink, so as to achieve the cooling effect.
  • If you need use for metal, hard wood, granite, stone, you can choose metal spindle, then metal spindle is much better than wood spindle.

Reviews

There are no reviews yet.

Be the first to review “9.0kw Long axis air cooled spindle motor”

Your email address will not be published. Required fields are marked *